This pack groups the highest-value WeldKing technician job packets so a repair can be run from one packet instead of bouncing between guide, manifest, and bench sheet manually.
| Model | Packet | Best used for |
|---|---|---|
| CoolArc160 | job packet | low OCV, fan-supply, and capacitor-board versus inverter-board repairs |
| CoolArc200 | job packet | input-sense, VRD, and wrong voltage-recognition complaints |
| CoolTIG220 | job packet | no TIG start, HF-versus-no-HF version faults, gas-path proving, and remote-branch separation |
| TIG200PACDC | job packet | DC-versus-AC TIG proving, pedal-branch faults, and gas-path complaints |
| CoolCut30 | job packet | high-versus-low OCV splits, 24 V support faults, and no-HF diagnosis |
| CoolCut40air | job packet | internal-versus-external air proving, dual-air faults, SG55-stack proving, and valve-path complaints |
| CUT40 | job packet | air-routing faults, start complaints, and guide-hardware proving |
| CUT65 | job packet | pressure-sensitive pilot, postflow-with-no-start, and guide-hardware separation |
| ThunderCut65 | job packet | delayed restrike, torch-head faults, pressure-window or RV1 branches, and guide-hardware complaints |
| MAG211 | job packet | chart-correct baseline, gas-solenoid proving, and spool-gun-only branch separation |
| MAG251 | job packet | ripple complaints, motor-direction issues, and spool-gun branch separation |
| MAG255 | job packet | crater-fill proving, spool-gun pins 1 and 9, and discharge-path branch separation |
| MigSonic145 | job packet | click-cycling, support-power faults, and gun or gas-side proving |
| MigSonic252S+SS20 | job packet | source-versus-feeder separation, frozen readouts, and spool-gun feed faults |
| MultiSonic220 | job packet | MIG-only faults, flashing display, feeder run-on, and process-state issues |
| PulseWave200 | job packet | TIG start, reset-state, AC/DC branch, and HF-related repairs |
MAG211: use the MAG211 job packet for chart-sensitive instability, no gas command, and one-gun-only behavior.MAG251: use the MAG251 job packet for ripple complaints and post-service feed-direction trouble.MAG255: use the MAG255 job packet for crater-fill behavior, spool-gun no-weld, and discharge-path trouble.MigSonic145: use the MigSonic145 job packet when a compact MIG clicks on and off, loses trigger after support-power trouble, or shows low output that still follows the machine. Keep stable 24 V, correct gun generation, and base-gun bare-wire feed with the tip removed ahead of any spool-gun or PCB blame.MigSonic252S+SS20: use the MigSonic252S+SS20 job packet when readouts freeze, gas stays open, or the feeder is blamed while the source already looks wrong. Prove the power source first with healthy readouts, jog or purge response, and idle gas behavior before feeder teardown.CoolTIG220: split HF-versus-no-HF version assumptions before staging internal parts or assigning board work in the packet.TIG200PACDC: use the TIG200PACDC job packet when DC TIG is healthy but AC is unstable, or only one pedal branch misbehaves. Keep simple DC TIG, remote-isolated local control, and 4K7 remote proof ahead of any broader AC-board conclusion.CoolCut40air: stage the job around internal-air versus external-air proof first, not around generic plasma-board suspicion.CUT40: use the CUT40 job packet for external-air routing, CB50 front-end, and guide-hardware complaints. Keep freehand cutting ahead of guide-hardware blame, and do not collapse it into the built-in-air CoolCut40air path.CUT65: use the CUT65 job packet for pressure-window, torch-head, and A81 hardware complaints on the 65 A external-air family. Keep freehand cutting ahead of stand-off or circle-kit blame.ThunderCut65: keep pressure-window, RV1, torch-head rebound, and guide-hardware branches active in the packet before internal escalation.CoolArc160: parts category, TIG kit 07003650, ground clamp 07000461, holder 07000460CoolArc200: parts category, TIG kit 07003750, adapter 07001825, ground clamp 07000462CoolTIG220: parts category, PRO17 torch WAT31100, FC25-HD 07002510TIG200PACDC: parts category, gas regulator branch 07000510, gas hose branch 072611120CoolCut30: parts category, electrode 07Y2517003, tip 07Y2517005, nozzle 07Y2517004CoolCut40air: parts category, electrode 07Y2517003, nozzle 07Y2517004, SG55 tip branch on the same official parts pathCUT40: parts category, guide carriage 07CV0037, extended tip 07PD0063-10CUT65: parts category, A81 torch 07001400, 2-leg stand-off 07CV0026, circle kit 07CV0052ThunderCut65: parts category, A81 ecosystem, guide carriage 07CV0051, stand-off 07CV0028MAG211: parts category, spool gun 07NS1000, U-groove drive roll 07000302MAG251: parts category, spool gun 07NS1000, drive-roll familyMAG255: parts category, spool gun 07NS1000, U-groove drive roll 07000302MigSonic145: parts category, NT-1 gun 07000422, SpoolKing-200 07NS2000, gas-side branchMigSonic252S+SS20: parts category, spool gun 07NS1000, drive roll 07NS1007MultiSonic220: parts category, aluminum kit XOM99035, spool gun 07NS1010, PRO17 torch WAT31100, pedal 07002510PulseWave200: parts category, PRO17 torch WAT31100, FC25-HD 07002510, FC25-WL 07002515